WINGS titanium                                        
Exhaust for the KTM 1190 / 1050 ADVENTURE & 1290 SUPER ADVENTURE

Natural  titanium  short           ............................................................           $929
Black  titanium  short              ............................................................           $949


+ shipping (quotes below) 


  1190 Installation Youtube video  

  shipping cost examples  
$18 - Port Macquarie, Hunter, Sydney metro, Brisbane metro, Melbourne metro
$22 - Adelaide / $36 - Perth / $38 - Darwin / $29 - Hobart / $59 - NEW ZEALAND

                                     WINGS CARBON                                        
Carbon fibre seat coolers kit for 1050ADV  / 1190ADV / 1190ADV R / 1290ADV

WINGS exhausts has designed a small selection of CARBON FIBRE accessories to compliment and exactly match the CF end caps and heat guards that come standard on the WINGS exhausts 
No matter how many aftermarket parts you have put on your bike, one is still missing. By looking at the pictures below you would notice that "Seat Cooler" improves the look of the bike significantly. It follows the lines of the bike in such a harmonious way as if it would be a part of the bike from the beginning. But "Seat Cooler" is not only beautifully designed and crafted from the prestigious carbon fibre. It's also functional because it eliminates the problem of overheating by leading the engine heat away from your legs and your seat towards the back."Seat Cooler" is made from carbon fibre, with a high gloss, clear ceramic coating which is UV, heat and scratch resistant. The quality is far above industry standard

Fully compatible with aftermarket PUIG and KTM "R" model engine guards.

Available in HIGH GLOSS CARBON and MATTE CARBON

                                                                         
        
 $359  (10% off / $316 for WINGS exhaust wholesale direct customers)

  spares  

$99   - cf end cap
$129 - cf end cap, rivets & rivet strip kit
$119 - cf heat shield kit
$65   - rear strap clamp
$39   - 34mm or 40mm baffle
$45   - 34mm or 40mm spark arrestor type baffle
$65   - damping wool
$15   - Viton rubber strip under clamp
$3     - special gas-tight rivets 





A few questions have been asked about side case compatibility. The manufacturer has responded: 
The WINGS 1290 Adv /1190 Adv muffler is narrower than the stock one, so the gap between the muffler and the side-case is larger. Besides this, WINGS is cooler than the original muffler therefore no heat problems were noticed. Exit angle and direction of the exhaust gases of the WINGS mufflers are exactly the same as at the original muffler. So far, no issues have occurred in this regard during testing. Long-term tests of WINGS muffler continue to eliminate any doubts about side-case compatibility.

  A few facts not widely known about WINGS exhausts  
It's been a misconception for years that WINGS is a "COPY" of another exhaust brand. This could not be further from the truth. The WINGS design was "first on the block".

  Unique to the WINGS KTM 1190 exhaust  
Just as the WINGS 990SMT exhaust had a carbon fibre end cap designed to perfectly sync with the bikes' design, the all new 1190 end cap is also exclusively designed to match the lines of the newest big KTM ADV. 

  Common to all WINGS exhausts  
Use of Japanese titanium, arguably the very best quality available.

  New Clamp Strap Liner Material   - Viton® DuPont™  fluoroelastomer
The World's First Fluoroelastomer
Viton® fluoroelastomer is the most specified fluoroelastomer, well known for its excellent (400°F/200°C) heat resistance. Viton® offers excellent resistance to aggressive fuels and chemicals and has worldwide ISO 9000 and ISO/TS 16949 registration.

  New UV proof coating on all carbon fibre surfaces  
The new super hard coating is also scratch resistant and retains it's high gloss finish for the life of the exhausts.

  WINGS only uses the highest quality and most expensive rivets available 
Apart from the obvious strength benefit, they have the unique ability to expand to "gas-tight" size when assembling after a re-pack.
Because of the high cost, these rivets are only used by manufactures who strive for ultimate quality in their products. Use of these rivets is unique to WINGS exhausts... it's all in the attention to detail.

   Old world artisanship meets industry leading CAD/CAM/CNC technology to reproduce a perfect clone of every product that gets shipped   


  NOTE: While the manufacturer continues to include 2 baffle sizes to his European customers, We have chosen to keep the price as low as possible by  only having the larger "EU 40mm" baffle included in the 1190 exhaust kit. Any other additional baffle can be requested at an extra cost, or as a substitute  for the "default EU 40mm" item at no extra cost.  


HitCounter


 
     
 

MOTOTOYS * Newcastle NSW * Mob# 0400284840 * ABN 34 265 258 772

  
  Site Map